1 00:00:00,400 --> 00:00:03,400 The Usage Ranking names the older Slab Rebar command. 2 00:00:03,680 --> 00:00:07,400 This installation exposes Slab Rebar 2 .0 and Slab 3 00:00:07,400 --> 00:00:08,080 Rebar plans. 4 00:00:08,460 --> 00:00:11,680 This guide demonstrates the installed 2 .0 settings interface. 5 00:00:12,400 --> 00:00:14,320 Select Structural Floors and Finish. 6 00:00:14,740 --> 00:00:18,800 Our practice floor is 9075 x 7000 mm, 7 00:00:19,020 --> 00:00:20,480 300 mm thick. 8 00:00:21,000 --> 00:00:23,320 Creation is blocked by a missing method in the 9 00:00:23,320 --> 00:00:26,480 installed add -in, so the following screens demonstrate settings 10 00:00:26,480 --> 00:00:27,340 and previews only. 11 00:00:28,867 --> 00:00:31,407 Select the floor in the upper left list. 12 00:00:31,787 --> 00:00:33,047 Cover is in millimeters. 13 00:00:34,007 --> 00:00:36,567 Hat Factor sets the support reinforcement length as a 14 00:00:36,567 --> 00:00:39,167 fraction of span, such as L over 4 or 15 00:00:39,167 --> 00:00:39,787 L over 5. 16 00:00:40,447 --> 00:00:43,647 Rounding controls rounded lengths, and min -span filters short 17 00:00:43,647 --> 00:00:44,007 spans. 18 00:00:44,867 --> 00:00:47,207 Beam Anchor A and Slab Anchor B apply to 19 00:00:47,207 --> 00:00:48,067 support reinforcement. 20 00:00:48,747 --> 00:00:51,487 Bottom Anchor and Top Anchor separately control anchorage of 21 00:00:51,487 --> 00:00:52,887 the full bottom and top layers. 22 00:00:53,367 --> 00:00:56,187 Check the detected panel list before changing edge behavior. 23 00:00:57,700 --> 00:01:01,060 For a bottom -only example, enable Bottom Layer Draw 24 00:01:01,060 --> 00:01:04,760 and disable Top Layer, Hat Reinforce, Distribution Bars, and 25 00:01:04,760 --> 00:01:05,200 Spacers. 26 00:01:05,600 --> 00:01:09,020 Here, Bottom X is D12 at 200 mm, and 27 00:01:09,020 --> 00:01:10,780 Bottom Y is D10 at 150. 28 00:01:11,340 --> 00:01:13,800 The third bottom field is hook length, not another 29 00:01:13,800 --> 00:01:14,160 spacing. 30 00:01:14,900 --> 00:01:17,360 Invert Layer reverses the stacking order of the directions. 31 00:01:18,220 --> 00:01:19,940 Preview Bottom shows the proposed layout. 32 00:01:20,140 --> 00:01:21,800 It does not create rebar elements. 33 00:01:23,560 --> 00:01:25,860 Enable Top Layer Draw for a full top mesh. 34 00:01:26,220 --> 00:01:28,480 Here, both directions are D12 at 200. 35 00:01:28,960 --> 00:01:32,140 Hat Reinforce is a separate, local top reinforcement group, 36 00:01:32,160 --> 00:01:34,640 with its own X and Y diameter and spacing. 37 00:01:35,280 --> 00:01:38,220 Top Dist Rebar adds distribution reinforcement for that arrangement. 38 00:01:38,880 --> 00:01:41,960 Spacer, Chair, or C -Hook uses its own diameter, 39 00:01:42,240 --> 00:01:43,860 two placement steps, and hook length. 40 00:01:43,860 --> 00:01:47,520 The example uses D10 at 1200 by 1200 with 41 00:01:47,520 --> 00:01:48,560 a 200 mm hook. 42 00:01:50,287 --> 00:01:53,827 Select a panel row before applying panel actions. 43 00:01:54,587 --> 00:01:58,467 Full Hat changes the panel to Full Support Reinforcement 44 00:01:58,467 --> 00:01:58,927 Coverage. 45 00:01:59,587 --> 00:02:03,687 Full Span Anchor and Pick Edge work on particular 46 00:02:03,687 --> 00:02:04,687 support edges. 47 00:02:05,087 --> 00:02:08,187 Verify the highlighted edge and resulting preview. 48 00:02:09,007 --> 00:02:13,007 Merge Mode and Auto Merge combine eligible panels. 49 00:02:14,307 --> 00:02:18,227 Delete Panels removes panel definitions from this tool, not 50 00:02:18,227 --> 00:02:19,227 the structural floor. 51 00:02:19,767 --> 00:02:23,387 These controls need a model with meaningful panel boundaries 52 00:02:23,387 --> 00:02:24,627 to demonstrate their effect. 53 00:02:26,393 --> 00:02:30,053 Skip Top and Skip Bot operate on the selected 54 00:02:30,053 --> 00:02:30,793 panel rows. 55 00:02:31,793 --> 00:02:34,493 Pick Skip Edge operates on a chosen edge. 56 00:02:35,273 --> 00:02:38,753 Always compare the correct preview layer after applying an 57 00:02:38,753 --> 00:02:39,213 override. 58 00:02:39,713 --> 00:02:43,673 A Preview Visibility button only shows or hides the 59 00:02:43,673 --> 00:02:44,573 drawing in the tool. 60 00:02:44,953 --> 00:02:48,713 The Draw checkbox controls whether that reinforcement group is 61 00:02:48,713 --> 00:02:50,233 requested during creation. 62 00:02:50,553 --> 00:02:52,073 These are different decisions. 63 00:02:53,660 --> 00:02:57,520 Slab Rebar Info List displays the configured reinforcement for 64 00:02:57,520 --> 00:02:58,400 the selected floors. 65 00:02:58,720 --> 00:03:01,260 It is a settings summary, not a report of 66 00:03:01,260 --> 00:03:02,340 bars already created. 67 00:03:02,840 --> 00:03:05,860 Select All and Unselect All control which rows receive 68 00:03:05,860 --> 00:03:07,040 a quick layout change. 69 00:03:07,320 --> 00:03:09,740 Use the language selector for the English interface. 70 00:03:10,300 --> 00:03:12,380 Horizontal scrolling reveals additional columns. 71 00:03:14,127 --> 00:03:18,167 Quick Layout has enabling checkboxes for top, bottom, additional 72 00:03:18,167 --> 00:03:21,767 top reinforcement, cover, hat distribution, and spacers. 73 00:03:22,047 --> 00:03:23,947 Check only the groups you intend to change. 74 00:03:24,327 --> 00:03:27,187 Set Diameter and Spacing independently for X and Y, 75 00:03:27,367 --> 00:03:29,567 plus hook or anchor options where available. 76 00:03:30,247 --> 00:03:32,207 Apply updates the selected floors settings. 77 00:03:32,487 --> 00:03:34,387 It is not the Create Rebar operation. 78 00:03:35,107 --> 00:03:37,067 Cancel leaves the quick changes unapplied. 79 00:03:38,827 --> 00:03:41,907 Create Rebar was tested with the simple bottom -only 80 00:03:41,907 --> 00:03:42,307 case. 81 00:03:42,567 --> 00:03:45,387 The installed add -in reports a missing Rebar API 82 00:03:45,387 --> 00:03:47,307 shim create from curves method. 83 00:03:47,307 --> 00:03:50,447 No successful slab reinforcement output was verified. 84 00:03:50,747 --> 00:03:53,667 Changing spacing or cover will not repair a missing 85 00:03:53,667 --> 00:03:54,047 method. 86 00:03:54,267 --> 00:03:56,227 Keep the log for the add -in provider and 87 00:03:56,227 --> 00:03:59,627 use a compatible installation before completing the creation walkthrough. 88 00:03:59,867 --> 00:04:02,847 The supplied practice file contains the structural floor. 89 00:04:03,067 --> 00:04:05,107 No slab reinforcement result is claimed.